All times are UTC - 5 hours




Forum locked This topic is locked, you cannot edit posts or make further replies.  [ 1 post ] 
 

White Lightning 2-Light Sample Portrait Setup
Author Message
PostPosted: Fri Mar 23, 2007 11:17 am 
This sample two-light setup uses two White Lightning X-Series X800 Flash Units to light both your subject and your backdrop, but gives you the effect of a "three-light" setup with the use of the reflector panel. This setup could be used for portraits and/or headshots.

Image

One flash unit (unit 1) is used as a Main Light, softened with our OB47 Large Octabox or FOB47 Large Foldable Octabox. Using the octabox produces a soft, diffused light source with a rounded catchlight. The closer that the octabox is placed to the subject, the softer the output will be. You can begin by placing this light as close to your subject as it can get while still being outside of the framed shot, then adjust forwards and backwards. This unit is set as the most powerful flash in the setup, positioned at roughly a 45-degree angle.

The second “light” is the CRK42 Reflector Panel. The white bounce side of this 5-in-1 reflector panel kit is used as a Fill Light, to "fill in" the shadows cast by the main light (the silver or gold bounce surfaces may be used here as well - using the white surface creates a soft, natural bounce). The panel is positioned on the opposite side of the subject so that it catches light from the main light and bounces it back towards the subject. The CRK42 can be held by an assistant or used with our RBH2566 Reflector Kit Mounting Arm on either a 10-foot or 13-foot light stand.

The second flash unit (unit 2) is used as the Background Light, diffused with the U32TWB Shoot-Thru Umbrella. The unit can be positioned on a 10-foot stand (LS3050), on a 13-foot stand (LS3900 or TS13AC) or on the short LS1100 backlight stand, angled up towards the center of the backdrop behind the subject’s head. Depending on the size of the backdrop area that will be visible in the frame, you can adjust the positioning of the unit and choose a stand that gives you the flexibility that you need for height adjustment. Using the “shoot-thru” white umbrella will soften the total output while spreading it out to cover a wider area.

With a white backdrop, begin by setting the output of this unit at full power, then adjust the output as you take your meter readings, metering the background separately. To ensure that the background is bright white and that the shadows from the subject are overpowered, the background should meter approximately two f-stops brighter than your subject. With a dark or textured backdrop, you can begin by setting the output lower.

Using two X800 units allows you to get a true "What-You-See-Is-What-You-Get" modeling preview, as you can adjust each unit's modeling lamp output simultaneously with the flashpower output (adjusting both sliders together) to maintain the accurate preview despite output adjustments and various accessory use.

To connect your setup, you'll simply plug each flash unit into your standard Ac power source (or Vagabond system). You can then connect one flash unit to your camera with the provided sync cord, and allow the other units to fire simultaneously with their built-in slaves. You could also use the CyberSync Radio Remote Control System or LG4X Wired Remote to control triggering and/or output.


Top
  
 

Display posts from previous:  Sort by  
Forum locked This topic is locked, you cannot edit posts or make further replies.  [ 1 post ] 

All times are UTC - 5 hours


Who is online

Users browsing this forum: No registered users and 1 guest


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Jump to:  
cron
Skin created by © gokin, reklama w internecie reklama internetowa
Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group