All times are UTC - 5 hours

Forum locked This topic is locked, you cannot edit posts or make further replies.  [ 1 post ] 

Color Temperature / Color Balance
Author Message
PostPosted: Mon Mar 12, 2007 2:30 pm 
Achieving Excellent Color Balance with Studio Flash

In order to achieve good color balance with studio flash, the user must understand the factors that affect color.

Cameras with built-in flash need only establish color balance parameters from a single, unchanging flash source and are normally set to “flash” setting for proper color.

But color balance with studio flash is affected by a number of variables including the color balance of the flash units themselves, changes of color introduced by the shooting environment, changes caused by light modifiers and the artistic perception of how colors should look in a shot.

>> Click Here for more info on Flash Duration

The first rule of seasoned professionals is that there is no reliable camera setting that considers all of these factors. The assumption that all lights rated at a certain color temperature (such as “5600°K”) produce the same color balance is incorrect. In particular, the “flash” setting of most cameras is not accurately matched to most studio flash systems. There is simply no automatic method of setting accurate color balance in the camera. Fortunately, there are two methods of easily achieving good color balance.

Custom White Balance

The proper method to do this in the camera is to follow the camera manual’s instructions for setting a Custom White Balance. When you do this, a test picture is taken with the lights set up and adjusted for the pictures you are about to take. The camera then calculates the appropriate adjustments needed to render neutral colors (greys and whites) taken in this lighting environment free of colorcasts and errors. Once this is done, the entire color spectrum will be reproduced as accurately as the particular camera allows for. Using custom white balance is the preferred method of color balancing if you are shooting jpg pictures or when you wish to avoid post processing of your shots.

RAW Capture

With the evolution of software programs such as Adobe Photoshop, most professionals prefer to shoot their important sessions with the camera set to “RAW” mode rather than jpg. This method saves the information directly from the camera sensor to the memory card, bypassing any processing in the camera. Thus, you can shoot spontaneously and avoid all color balance, contrast and sharpness settings in the camera with the assurance you can more accurately set these parameters after the fact, in post processing.

A word of warning: Shooting in RAW cannot undo burned out whites, out-of-focus shots or improper ISO and shutter speeds settings from the camera and thus requires you to set these parameters properly in the camera.

>> Click Here for more info on Exposure, Histograms and Flashmeters

The proper method for shooting RAW is to make sure that you have a known-neutral object in the scene. If you are shooting a series of pictures under the same illumination, you can place a white or grey white-balance test card in the first shot of a series, then remove it for subsequent shots. Many shooters prefer to leave a white balance card at the top or bottom of every shot where it can be cropped out later, as this gives them the freedom to make significant changes in the lighting with the assurance each shot can be critically color-balanced in post processing. If you are shooting against a neutral grey or white background, you can often omit the white balance card and use the background as a neutral object. But beware that all grey or white backgrounds are not truly neutral and that filters, gels, etc. must not tint the light falling on the background.

The procedure for post processing RAW shots is really quite simple. In Adobe Bridge (part of Photoshop CS2 and CS3), you can open your entire folder of pictures. Select a picture that contains a white balance card and simply place the eyedropper tool on the white or neutral grey portion of the card. The software will instantly calculate perfect color balance for the entire image.

From there you can adjust contrast, exposure, cropping, sharpness and other attributes of the shot. If you have shot a series of pictures under the same illumination, you can then copy and paste any or all of these parameters to all the other shots in the series.

In RAW processing, the original image data is normally saved to the hard drive and a copy of the image containing your adjustments is output to a new file as jpg, tiff, Photoshop or other file type. If you are later unhappy with your post processing it’s an easy matter to reopen the image in RAW, apply new settings, and output new final files. Smart shooters always archive their original RAW shots.


Display posts from previous:  Sort by  
Forum locked This topic is locked, you cannot edit posts or make further replies.  [ 1 post ] 

All times are UTC - 5 hours

Who is online

Users browsing this forum: No registered users and 1 guest

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Jump to:  
Skin created by © gokin, reklama w internecie reklama internetowa
Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group